Placard wardrobe kit with two sliding doors that includes all the necessary hardware and profiles for assembly and installation, except for the panels. This system of hardware and profiles allows you to create your own wardrobe or dressing room with two bottom-mounted sliding doors that glide smoothly and quietly. The Placard sliding system features lower carriages with steel ball bearings, door height adjustment of ± 5 mm, and a spring locking mechanism that facilitates door installation. It includes an anti-derailment system using a spring in the lower carriage and an adjustable anti-jump stop on the upper runner. It also includes a braking device for smooth opening and closing of the doors, with a maximum weight of 30 kg per door. This system offers greater holding power thanks to its hydraulic piston, achieving a progressive and precise closing. The doors are equipped with a U-shaped crossbar and Sharp aluminum handle profiles , designed for doors with thicknesses of 16/18/19 mm.
Sliding system for creating a wardrobe with two bottom-hung sliding doors. Suitable for doors with thicknesses of 16/18/19 mm and a Sharp square handle profile. Panels not included .
It incorporates a brake device for smooth opening and closing for a load capacity of up to 30 kg per door.
Consisting of carriages with ball bearings, height adjustment of ± 5 mm, and a spring locking system that facilitates door installation. It also includes an anti-derailment system using a spring in the lower carriage and an adjustable anti-jump stop on the upper runner.
The handle profiles and the top and bottom rails are supplied in a measurement of 2,350 mm to be cut to the desired size.
Includes a hardware set for two doors, top and bottom rails, handle profiles and a U-shaped crossbar. Profiles made of aluminum and finished in black/white/matte anodized paint.
16mm black EAN 8432393300498
16mm matt anodized EAN 8432393330976
18 mm matte anodized EAN 8432393330983
19mm white EAN 8432393330990
19mm black EAN 8432393331010
19mm matt anodized EAN 8432393331003
Protector for the bottom of kitchen base units , specially designed to protect the bottom of the units from moisture and splashes. It consists of an aluminium sheet sized to the module size, which is indicated with a plastic rubber that adapts to and insulates the module. Easily cut to adapt to other module sizes.
Bottom protector for the lower modules of kitchen furniture.
Sized for modules with a width of 1000/900/800/600 mm, depth of 580 mm and board thickness of 16 mm.
Model dimensions: 968/868/768/568 mm x 580 mm.
Easily cut to fit other module sizes.
Made of aluminum and plastic.
He 12V DC constant voltage converter is designed for luminaires of technology LED of constant tension and is characterized by its protection against overheating and short circuits.
It has interchangeable cable offering the possibility of connecting another cable to the converter with a different plug, depending on the market it is intended for.
The housing is made of black plastic with class II protection, it has a 6-output MINILED distributor and a 2-meter power cable.
Version 72W 12v:
Constant voltage converter for LED technology fixtures.
Power 72W.
Input 100-240V AC - 50-60Hz.
Output 12V DC.
Suitable for dry areas, IP20.
Includes 6-output MINILED distributor.
Cable length 2 m.
Allows you to connect another cable with a different plug (depending on the market).
Made of plastic with a black finish.
Version 50W 12v:
Constant voltage converter for LED technology fixtures.
Power 50W.
Input 100-240V AC - 50-60Hz.
Output 12V DC.
Suitable for dry areas, IP20.
Includes 6-output MINILED distributor.
Cable length 2 m.
Allows you to connect another cable with a different plug (depending on the market).
Made of plastic with a black finish.
Version 6W 12v:
Constant voltage converter for LED technology fixtures.
Power 6W.
Input 180-240V AC - 50Hz.
Output 12V DC.
Suitable for dry areas, IP20.
Includes 6-output MINILED distributor.
Cable length 2 m.
Allows you to connect another cable with a different plug (depending on the market).
Made of plastic with a black finish.
Version 15W 24v:
24V DC constant voltage LED converter ideal for operating LED lights, such as the Neon Lynx strip or the Lynx 24V strips.
Constant voltage converter for LED technology fixtures.
Power 15 W.
Input 180-240V AC - 50Hz.
Output 24V DC.
Suitable for dry areas, IP20.
Includes 6-outlet AMP distributor.
Cable length 2 m.
Allows you to connect another cable with a different plug (depending on the market).
Made of plastic with a white finish.
FAQs - Frequently Asked Questions
What is the maximum power and how is it distributed among the MiniLED outputs of the converter?
This converter has a maximum power of 60W with 12V DC output, distributed among its 6 MiniLED outputs, allowing multiple LED devices to be connected simultaneously.
What features make this converter suitable for projects in dry areas (IP20)?
The converter is designed with IP20 protection, ideal for dry areas, and features an efficient power factor that optimizes energy consumption in lighting projects.
How compatible is the converter with standard plugs and how do I connect it?
It's compatible with Type C plugs and IEC 60320 C7 connectors, offering flexible connectivity thanks to its 2-meter power cable. It also allows you to connect other cables for different outlets.
What are the dimensions of the converter and what advantages does it offer for installation?
With compact dimensions of just 16.5 mm thick, the converter can be easily hidden in tight spaces or behind furniture, maximizing available space.
What safety measures does the converter include against overheating or short circuits?
It incorporates protection against overloads, electrical interference, and short circuits, ensuring safe and stable operation, even in intensive usage scenarios.
Placard wardrobe kit with two sliding doors that includes all the necessary hardware and profiles for assembly and installation , except for the panels. This system of hardware and profiles allows you to create your own wardrobe or dressing room with two bottom-mounted sliding doors that glide smoothly and quietly. The Placard sliding system features lower carriages with steel ball bearings, door height adjustment of ± 5 mm, and a spring locking mechanism that facilitates door installation. It includes an anti-derailment system using a spring in the lower carriage and an adjustable anti-jump stop on the upper runner. It also includes a braking device for smooth opening and closing of the doors, with a maximum weight of 30 kg per door. This system offers greater holding power thanks to its hydraulic piston, achieving a progressive and precise closing. The doors are made of a U-shaped crossbar and Wave handle profiles made of aluminum with a white finish , designed for doors with a thickness of 16 mm.
Sliding system for creating a wardrobe with two bottom-running sliding doors.
Boards are not included.
Composed of carriages with steel ball bearings.
The lower carriage has height adjustment ± 5 mm from the door.
The top and bottom rails are supplied in 2,350 mm measurements so they can be cut to the required length.
The handle profiles are supplied in a measurement of 2,350 mm to be cut to the desired size.
It includes an anti-derailment system using a spring on the lower carriage and an adjustable anti-jump stop on the upper skate.
It has lower carriage spring locking mechanisms that facilitate door installation.
It includes a brake device for smooth opening and closing of the doors.
The device has greater holding power thanks to its hydraulic piston, which achieves a progressive and precise closure.
The system supports a maximum weight of 30 kg per door.
Frequently Asked Questions
Is a recess in the boards necessary for the installation of the system?
No, the included hardware and components are designed for direct installation without the need for recesses in the panels, making assembly easier and reducing installation time.
What features does the soft-close system have?
The soft-close system includes hydraulic piston devices that allow for a cushioned and silent closing, preventing sudden slams at the end of the door's travel. This improves security and prolongs the life of the mechanism.
How do I adjust the leveling and locking mechanism?
The kit includes an adjustment system on the bottom track that allows the doors to be precisely leveled and secure in place once installed. This makes it easier to correct unevenness on the mounting surface.
What materials are used in hardware and how do they affect its durability?
The hardware is made of steel and aluminum with anodized or white-painted finishes, ensuring high corrosion resistance and a long-lasting appearance even in humid environments.
What is the RAL code for the Placard sliding door system's rails and handles?
The RAL of the gloss white finish on the tracks and handles of the Placard sliding door system is approximately 9003. The RAL of the anthracite grey finish is approximately 7043. The RAL of the black finish is approximately 9011.
Zero profile kit to create a composition with 1 or 2 holes, includes all the accessories necessary for assembly with fixing to the floor and wall.
Zero profiles and accessories for creating modular shelving. The profiles are made of aluminium and the joining accessories and supports are made of zamak, all with a textured black painted finish (RAL 9005). Thanks to its simplicity and design, you can quickly adapt the Zero system to any type of environment: home, dressing rooms, office and shops. You can combine different elements to create your ideal composition: wooden or glass shelves, modules or small cupboards and hanging rails.
The Zero system is characterised by its ease of assembly, as it is not necessary to use any tools for adjustment. Adjust and position the shelves without having to disassemble any element and without special tools. Its great load capacity is noteworthy, as it can support more than 100 kg per shelf/module . In addition, with its innovative Zero fixing system, its clamping force increases as the weight it supports increases. The profile can be fixed using different mounting methods, fixing to the wall, floor or ceiling or combinations of both.
The Zero system components include all the accessories necessary for assembly.
Complete kit of profiles to create a composition of 1 space. These profiles must be purchased together with the Zero range supports to create different combinations of shelves, modules and hanging bars.
The kit consists of 2 profiles with a length of 2,115 mm, 2 profiles with a length of 210 mm, 2 wall fixings, 2 profile joints, 2 levellers, 2 profile caps and mounting screws.
Its design adapts to all types of environments and spaces: home, dressing rooms, office and shops. Combine the accessories with the profiles to create your ideal composition: wooden or glass shelves, modules or small cabinets and hanging rails.
Easy installation by fixing the profile to the wall and floor. Multiple combinations with wooden, glass, modular or bar shelf supports.
Made of aluminium and zamak in textured black painted finish (RAL 9005).
Complete kit of profiles to create a composition of 2 spaces. These profiles must be purchased together with the Zero range supports to create different combinations of shelves, modules and hanging bars.
The kit consists of 3 profiles of length 2,115 mm, 3 profiles of length 210 mm, 3 wall fixings, 3 profile joints, 3 levellers, 3 profile caps and mounting screws.
Its design adapts to all types of environments and spaces: home, dressing rooms, office and shops. Combine the accessories with the profiles to create your ideal composition: wooden or glass shelves, modules or small cabinets and hanging rails.
Easy installation by fixing the profile to the wall and floor. Multiple combinations with wooden, glass, modular or bar shelf supports.
Made of aluminium and zamak in textured black painted finish (RAL 9005).
Essential accessories:
Kit of brackets for 4 wooden shelves and 1 hanging bar length 1m Zero
Bracket kit for 1 wooden shelf, 1 module and 1 hanging bar 1m long Zero
Kit of supports for 3 wooden shelves and 1 module for the Zero structure
FAQs - Frequently Asked Questions
How to make a dressing room structure with the Zero system?
The following video shows how to easily assemble the Zero system.
Neco wardrobe kit with two sliding doors that includes all the hardware and profiles necessary for its assembly and installation except the panels . The Neco sliding system has the best quality in sliding door systems at the best price. With a load capacity of 50 kg of weight per door. Its carriages have steel ball bearings and are valid for the right or left door. It also includes euro thread screws for the assembly of the carriages and skates. This system includes anti-derailment on both the interior and exterior door and adjustable brakes to adjust the closing of the door that do not require machining on the upper rail. The assembly is easy to install since it includes clips for the lower skates which offer a simpler placement of the doors. First the doors are hung on the upper rail and finally the lower skates are placed. The system has a reduced opening loss of 21 mm which can be reduced to 0 by removing a piece of the interior carriage, in this way the doors could be crossed in their entirety. This makes it easier to install internal drawers or removable elements. The door composition includes a straightening profile and Styl handle profiles made of aluminium painted steel with protective film, designed for doors with a thickness of 16 mm.
Sliding system for creating a wardrobe with two hanging sliding doors.
Boards are not included.
The system supports a maximum weight of 50 kg per door.
Composed of carriages with steel ball bearings.
The top and bottom rails are supplied at a length of 2300mm to be cut to the desired length.
The styl handle and straightener profiles are supplied in a measurement of 2300mm to be cut to the desired size.
Includes euro thread screws for mounting the carts and skates.
Valid for right or left door.
The upper carriages and lower skates are made of sheet steel.
Includes anti-derailment on both the interior and exterior doors.
It has adjustable brakes to adjust the closing of the door.
The positioning of the upper brake does not require pre-drilling.
Pull-out trolley for lower kitchen units made of steel and in an anthracite grey finish, ideal for small spaces or auxiliary furniture. Easy installation and fully adjustable door. The structure is made of chrome-plated steel with three levels and includes fully extendable, soft-close roller guides that allow the system to glide smoothly and prevent slamming. Load capacity up to 30 kg.
Valid for modules from 300mm minimum interior width and minimum depth of 480mm.
Valid for modules from 400 minimum interior width and minimum depth of 480mm.
Load capacity up to 30Kg.
Steel structure in anthracite grey finish with height-adjustable baskets.
Left-hand side fixing by means of 2 roller guides with full extension and cushioned closing.
Total door adjustment.
Product Features
It consists of 2 plinth bars at 2.35 m.
Includes 2 90º joining accessories and 2 flexible joints.
Height 100/150 mm.
Plastic with black or aluminum finish.
Kitchen skirting board kit formed by 2 plinth bars and the connecting accessories to provide a practical and aesthetic solution to your kitchen. Protects the lower kitchen cabinets from damage and from the penetration of liquids and dust into the space between the cabinets and the floor.
The plinth bars are supplied in 2.35 meters long and with integrated seal and are resistant to moisture, chemical agents and UV rays. The joining accessories consist of 2 joints to form 90º angles and 2 flexible joints for added versatility and to be able to adjust the skirting boards to any angle. Both the skirting board bars and the accessories are supplied in Two heights (100 mm and 150 mm) , are made of PVC and are incorporated in two finishes, in satin and black anodized finish . The satin anodized finish is supplied with protective plastic film.
Furniture pistons that allow the opening of wooden or aluminium framed doors. They provide a cushioned lowering of the swing door in kitchen, home and bathroom furniture. These shock-absorbing pistons are supplied individually bagged with assembly instructions. Each bag contains a piston, a side hook, a wooden door hook, a door hook with aluminium frame and the necessary screws.
Shock-absorbing piston for wooden or aluminium framed lift-up doors.
They provide a cushioned door lift for kitchen, home and bathroom furniture.
Piston force from 5 to 11 kg.
Piston stroke or travel 80/100 mm.
It can be mounted either on the right or left side of the furniture.
Individually packed in bags with assembly instructions.
Each bag contains 1 piston, 1 side hook, 1 hook for wooden door, 1 hook for door with aluminum frame and the necessary screws.
Made of steel and plastic with a metallic grey finish.
Universal cutlery trays for kitchen drawers with a straight design and large storage capacity for cutlery and other kitchen utensils, making the most of the space. Because they can be cut to size, they can be adapted for use with drawers mounted on standard width modules between 400 mm and 900 mm , depth between 450 mm and 500 mm with board thicknesses between 16 mm and 19 mm depending on the selected model.
Internal drawer cutlery tray sized for module drawers with a width from 400 mm to 1000 mm.
Adaptable to drawer depths between 450 mm and 500 mm with board thicknesses between 16 mm and 19 mm.
Can be cut to fit depths between 418mm and 482mm.
Made of grey/anthracite plastic
What is the RAL colour of the Optima cutlery trays?
The RAL colour of the white finish of the Optima cutlery tray is approximately 9003. The RAL colour of the grey finish of the Optima cutlery tray is approximately 7001. The RAL colour of the anthracite grey finish of the Optima cutlery tray is approximately 7043.
Self-extracting removable recycling bin for 40 cm module. Once installed in the unit , the bin is removed when the door is opened . It is an excellent option for sorting waste. It is made up of a highly rigid plastic structure together with fully removable ball guides, which allow the bin to slide smoothly for better access to its interior. The bin has a 30-litre bin with a handle for easy removal and cleaning.
For automatic installation, 40 modules are required with minimum internal measurements of depth 472 mm and height 445 mm and for manual extraction, 30 modules can be used. Its installation is very simple, allowing it to be installed in right or left opening modules and the structure of this waste bin is fixed to the bottom of the modules. Made of steel and plastic in an anthracite grey finish. Includes all the mounting accessories necessary for installation in the kitchen.
The handle for sliding wooden doors Pasadena It is ideal for both decoration and continuous use thanks to its robust design. It is made of steel , with a textured black finish.
It is composed of two pieces : an exterior handle of easy grip and an interior plate with a fingernail to open the door without damaging the walls . It is suitable for doors 35 to 45 mm thick and has a length of 240 mm.
It is recommended to install the handle vertically . To do this, only two 10mm diameter drill holes will be required. screws M8 for mounting come included . In addition, each handle is individually wrapped to prevent bumps or scratches.
Handle for hanging wooden sliding doors, consisting of two parts: an easy-to-grip exterior handle and an interior finger-grip that won't damage walls. You can open the door from both sides comfortably and easily.
Length 240 mm. Suitable for center distances (distance between mounting holes) of 180 mm. Suitable for doors 35 to 45 mm thick.
Easy installation, as the necessary screws are included. Only two 10 mm diameter holes are required. No door carving or installation experience is required.
Its rounded design provides a comfortable feel and protects your hands from damage. Pieces are also shipped individually to prevent scratches.
It is made of steel with a textured black finish.
Product Features
Kit of hardware required for the assembly of an external drawer with a height of 105 mm and depth of 270/300/350/400/450/500 mm, except for the border, back and bottom.
Includes full extension guides, a set of ribs and a set of front hooks for the outer drawer.
The guides are fully extendable with soft closing and a maximum load of 30 kg.
Made of anthracite grey or white painted steel.
The Concept kitchen and bathroom drawer It is available in kit format with all the necessary hardware for assembly. It also stands out for its great load capacity which can support up to 30 kg per drawer. Includes full extraction guides with soft closing , set of hooks and ribs Available in white or anthracite grey painted finish. You will only need the boards cut to the correct dimensions for the bottom, back and drawer border.
Product Features
Kit of hardware required for the assembly of an external drawer with a height of 105 mm and depth of 270/300/350/400/450/500 mm, except for the border, back and bottom.
Includes full extension guides, a set of ribs and a set of front hooks for the outer drawer.
The guides are fully extendable with soft closing and a maximum load of 30 kg.
Made of anthracite grey or white painted steel.
The Concept kitchen and bathroom drawer It is available in kit format with all the necessary hardware for assembly. It also stands out for its great load capacity which can support up to 30 kg per drawer. Includes full extraction guides with soft closing , set of hooks and ribs Available in white or anthracite grey painted finish. You will only need the boards cut to the correct dimensions for the bottom, back and drawer border.
Product Features
Synchronized full-extension drawer guides for drawers with depths from 290 mm to 490 mm. Designed for home furniture.
They have a hook to facilitate the quick assembly/disassembly of the drawer on the guides.
Three-way adjustment, vertical +3 mm, horizontal ±1.5 mm and depth +3 mm.
They have self-closing and a damping piston on both guides, which provides a soft closing of the drawer.
Maximum load 30 kg. Supplied in complete sets with right and left hands.
Its rolling is carried out on delrin rollers that allow horizontal and vertical guidance.
Silver concealed drawer slides are high-quality and perform better in home furnishings. These slides provide full drawer extension. They feature self-closing and a damping piston on both slides, providing a soft-close drawer. They also feature a locking catch for easy assembly and quick disassembly of the drawer from the slides.
FAQs - Frequently Asked Questions
How to install the Silver full extension drawer runners with hook?
The following video shows how to install the Silver full-extension drawer slides with hooks.
How do I adjust the guides for Silver full-extension drawers with hooks?
The following video shows how to adjust the Silver full-extension drawer guides with hooks.
Are the drawer dimensions of a Silver full-extension guide with a hook compatible with a Slippe guide, partial and/or full-extension with a hook?
Yes, the drawer dimensions are the same between the Silver and Slippe guides with partial and/or full extension and hook.
Are the drawer dimensions of a Silver full extension guide with hook compatible with a Silver full extension guide with pivot?
No, the drawer measurements are different between them.
Product Features
Integrated motion sensor that turns on when approaching within 1.5 meters and turns off the light after 15 seconds after leaving the detection zone.
Removable battery operation, which can be recharged using a 5V DC 1A mobile charger with a micro USB type B plug (not included) without having to remove the bar.
The tube can be cut to fit the required size.
Mocha/anodized aluminum bar with semi-rigid PVC rubber to prevent noise from the hangers.
Very easy wireless installation thanks to the side brackets and mounting screws included.
Sensor detection range: 1.5 meters.
Sensor detection angle: 90°.
Number of LEDs: 30.
Color temperature: Natural white (4,000K).
Luminous flux / Brightness: 30 lm.
Power: 0.6W.
Lighting angle: 120°.
Protection class: IP20.
Hanging bar for wardrobe or dressing room with LED lighting and motion detector fed with a removable battery The battery is located in one of the side supports hidden behind a cover and can be easily recharged using a 5V DC 1A mobile charger with a micro USB type B plug (not included) without having to remove the bar. The battery has an LED indicator that changes from red to green when charging is complete after approximately 4 hours.
His built-in motion sensor It allows the light to turn on when approaching within 1.5m and will turn off the light after 15 seconds after leaving the detection zone.
The tube is made of aluminum with a semi-rigid PVC rubber to avoid noise from the hangers and can be cut to fit the interior measurement of the furniture.
Simple wireless installation thanks to the supplied side brackets and mounting screws. The ideal solution for lighting the inside of wardrobes to make it easier to locate clothing in the dark.
Removable battery operation, which can be recharged using a 5V DC 1A mobile charger with a micro USB type B plug.
Product Features
Dish drainer designed for modules from 600 to 900 mm with board thicknesses of 16, 18 or 19 mm.
It has a large storage capacity, with a shelf for glasses and another for 21/25/29/33 plates, with a drip tray that prevents water from damaging your furniture.
It is very easy to assemble and clean, you just have to screw the anchors into the kitchen cabinet and place the trays.
Made of steel with a rust-resistant painted aluminium finish, with grey plastic anchors to the module and a transparent plastic drip tray.
It is supplied individually packaged, with everything necessary for installation, including screws for mounting in the cabinet.
He Suprastar dish drainer It is designed to organize dishes in your kitchen cabinets. It has a shelf for glasses and another for plates, with a drip tray that prevents water from damaging your furniture.
It stands out for its large storage capacity and for being Very easy to assemble , just screw the anchors into the kitchen cabinet and place the trays. It is made of steel with a rust-resistant painted aluminium finish, with grey plastic anchors to the module and a transparent plastic drip tray.
Gola profile kit for kitchen module fronts without handles. The kit is composed of all the accessories necessary for assembly, it consists of 2 Gola profiles of 2,350 mm, 2 sets of plastic covers and 12 brackets with expansion screws. Gola profiles, together with their accessories, optimise the interiors of modules without losing linearity and following an avant-garde aesthetic.
One of the greatest advantages of Gola profiles lies in their ease of assembly thanks to its fixing bracket with expansion screw which simplifies the machining of the board thus saving effort and time in its installation.
The Gola kit is made of aluminum and is available in white, black and matte anodized finishes.
The visible faces of the profiles are protected by a protective film that prevents possible friction and damage.
Gola profile kit for kitchen module fronts without handles. The kit is composed of all the accessories necessary for assembly, it consists of 2 Gola profiles of 2,350 mm, 2 sets of plastic covers and 12 brackets with expansion screws.
Gola profiles, together with their accessories, optimise the interiors of modules without losing linearity and following an avant-garde aesthetic.
One of the greatest advantages of Gola profiles lies in their ease of assembly thanks to its fixing bracket with expansion screw which simplifies the machining of the board thus saving effort and time in its installation.
The Gola kit is made of aluminum and is available in white, black and matte anodized finishes.
The visible faces of the profiles are protected by a protective film that prevents possible friction and damage.
Upper Gola profile kit for module fronts.
The kit is composed of all the accessories necessary for assembly.
The code consists of 2 upper Gola profiles, 2 sets of side covers and 12 brackets with expansion screws.
The upper Gola profile is supplied in a measurement of 2,350 mm to be cut to the desired size.
Made of aluminum with black/white/anodized finish.
The Red Eye 4 sensor is a motion detection system with a timer . It turns on when its detection range is interfered with and turns off once the programmed time has elapsed, since the timer it includes is adjustable between 10 seconds and 3 minutes. The detection range of the sensor is 2.5 meters.
Rechargeable LED wall light with motion detector made of plastic with a metallic gray finish and is perfect for interior lighting of home furniture or transit areas: laundry room, garage, stairs, children's room, hallway, etc.
The integrated motion sensor , with a detection range of 2 meters in length at a 120º angle, keeps the luminaire on while it detects movement and turns off after 30 seconds when it stops detecting it.
This light features a rechargeable 850mAh lithium-polymer battery . Charging time varies depending on the charger's amperage, although we recommend using a 5V DC 1A charger with a micro USB type B connector for an estimated charging time of 2 to 2.5 hours. It has a battery life of 360 on-off cycles per charge before the battery runs out and has an LED charging status indicator that turns from red to green when fully charged.
Installation on the surface of the furniture by screwing the base or using an adhesive magnet (both included), and can be easily removed for recharging.
Low-consumption LED technology.
Integrated motion sensor: keeps the light on while it detects movement and turns off after 30 seconds when it stops detecting it.
Sensor detection range: 120°, 2 meters.
Wireless Lighting System: 850mAh rechargeable lithium polymer battery, rechargeable with a 5V DC 1A mobile phone charger with a micro USB type B connector.
360 power cycles per charge before the battery runs out.
LED charging status indicator.
Mounts on furniture surfaces using the screw-on base or adhesive magnet, and can be easily removed for recharging.
Number of LEDs: 9.
Color temperature: Natural white (4,000K).
Luminous flux / Brightness: 85 lm.
Power: 1W.
Lighting angle: 160 degrees.
Protection level: IP20.
FAQs - Frequently Asked Questions
Can the Kraz light be recharged with a mobile phone charger?
Yes, the Kaz light can be recharged with a mobile phone charger. The charger must have a micro USB type B connector and supply at least 5V DC.
How long does it take to charge the Kraz light?
Charging time will vary depending on the charger's amperage. 5V DC 1A chargers are recommended, so the estimated charging time is 2 to 2.5 hours.
How many cycles does the Kraz luminaire last?
This light has a battery life of 360 on-off cycles per charge before running out of power. It features an LED indicator that changes from red to green when fully charged after approximately 2.5 hours.
How does the motion sensor integrated into the Kraz LED luminaire work and what is its detection range?
The integrated motion sensor detects movement within a range of 2 meters and a 120° angle. The light automatically turns on when motion is detected and turns off 30 seconds after no activity is detected.
What type of rechargeable battery does the light use and how long does it take to fully charge?
The light uses a rechargeable lithium-polymer battery with a capacity of 850 mAh. The estimated charging time is 2 to 2.5 hours using a 5V DC 1A charger with a micro USB type B connector.
What installation options are available and how can the luminaire be securely attached?
The light can be mounted with screws on a piece of furniture or with an included adhesive magnet, allowing it to be easily removed for recharging. Both options are safe and practical.
What does the charging status LED indicate and how do I know when the battery is fully charged?
The charging status LED indicates that the battery is charging when it's on. When the LED turns off, the battery is fully charged and ready for use.
In what types of applications and environments is this luminaire ideal for use, considering its design and specifications?
This luminaire is ideal for high-traffic areas such as hallways, closets, laundry rooms, or stairwells, thanks to its compact design, natural white light (4000K), and motion sensor. Its simple installation and 360-cycle runtime make it perfect for areas without direct access to electricity.
The Plastwin table cable grommet is designed to hide the cables of electronic devices on desks, office tables or home furniture. Its discreet square design allows for complete integration into the furniture, although for its installation it requires a circular machining of Ø80mm. It has a cover that can be removed to pass the cables and plugs through. Once installed, to access the cables, remove the cover by pulling it slightly upwards. The Plastwin cable grommet is also available in a white or black finish and is supplied in packs of 6 grommets.
The multi-socket connector or tower of lifting sockets is designed to provide functionality with its complete integration in kitchen, office and home furniture. It is designed to be built into both high and low modules thanks to its retractable design that is easy to extract and manually hide. It adapts perfectly to desks already equipped with cable glands. It has three Schuko-type sockets with a maximum admissible power of up to 3500W – 16A and two USB connectors to charge 5V DC electronic devices (1 x 1A / 2 x 0.5A) ideal for recharging smartphones and tablets. Its installation is very versatile since it only requires a D. 60 mm machining and can be mounted on surfaces with great thickness, between 1 and 95 mm. In addition, it is fixed to the furniture without the need for tools thanks to a manual fixing nut. It also has a discreet LED power indicator and a 1.8 m cable with a plug for operation at 230V AC 50Hz.
Multi-connector for embedding in kitchen, office and home furniture.
Designed to be built into both high and low modules.
It features a retractable design with easy manual extraction and concealment.
Destined for the European EU market.
It has 3 Schuko type sockets with a maximum admissible power of up to 3500W – 16A.
It also has 2 5V DC USB connectors to recharge smartphones or tablets (1 x 1A / 2 x 0.5A).
For installation, a D. 60 mm machining is required.
It can be mounted on very thick surfaces, between 1 and 95 mm.
It is fixed to the furniture without the need for tools thanks to a manual fixing nut.
It has a power LED indicator.
It also has a 1.8 m power cable with a 230V AC 50Hz plug.
It is made of plastic with a black/white/aluminum finish.
(Version 2usb a + 1usbc):
It has 3 Schuko type sockets with a maximum admissible power of up to 3500W – 16A.
It also has 2 USB A connectors and 1 USB C connector, with a fast charging function and an application range of 5V-3A, 9V-2A, 12V-1.5A for USB A and 5V-3A, 9V-2A, 12V-1.67A for USB C.
FAQs - Frequently Asked Questions:
How can I flush mount a removable Vertikal multi-connector in the cabinet?
The following video shows how to easily assemble the Vertikal removable multi-connector.
Are the USB connectors on the Vertikal multi-connector used to charge devices or are they also suitable for data transfer?
The USB connectors on the Vertikal multi-connector are for exclusive use to charge 5V DC - 2.10A (2x1.05A) electronic devices.
Can the Vertikal multi-connector be installed in high and low modules?
The Vertikal multi-connector can be opened both upwards and downwards. It is designed to be built into both high and low modules thanks to its retractable design that is easy to extract and manually conceal. Its innovative design allows for its complete integration into kitchen, office and home furniture, in low modules with the opening by pulling it upwards and in high modules by pulling it downwards.
Hanging kit for upper cabinet units in kitchen, bathroom, and home furnishings. It stands out for its ability to withstand heavy loads of up to 65 kg and for its ability to adjust the module's position laterally, in height, or in depth. They are mounted on the wall using a plate and are hidden from view once mounted in the unit. The only visible point from inside the unit is a small machining process that must be performed to adjust the module once it has been hung.
Hanging kit for upper modules in kitchen, bathroom and home furniture.
The hangers are hidden once the upper cabinets are assembled.
For modules between 600 and 1,000 mm high and 300 to 350 mm deep.
They have right and left hands for placement on the furniture.
They can be adjusted once the module is hung with a machining diameter of 18 mm.
With 3 adjustments: side 16 mm, height up to 18 mm and depth up to 25 mm.
The hangers are mounted on the wall using the included bracket.
The fixing is done on the side of the independent module of the top cover.
Requires pre-drilling with a diameter of 10 mm for assembly.
Each set has a load capacity of 65 kg.
For better fixation, it includes a rotating pin that is fixed to the module by moving the lever.
It is recommended to use a Philips screwdriver no. 2 Ø6 or Pozidrive no. 2 Ø6.
Made of steel with a galvanized finish.
The kit includes everything needed to assemble two 30x15 mm Silk wardrobe rods : the tube, the side supports, and the M6 screws for assembly. The tube has a co-extruded PVC rubber to prevent noise from the hangers.
Available in two tube sizes: 750 mm and 1150 mm . The 1150 mm kits also include 2 central supports to provide greater rigidity to the assembly. The side supports allow two types of mounting: on the sides of the module with a 3.5 diameter wood thread screw or top mounting with the M6x40 mm screws included. In compliance with ISO: 7170:205, the bar and supports can support a maximum weight of 40 kg/meter evenly distributed.
Tube length: 750mm/1150mm.
The kit includes everything needed to mount two 30x15mm Silk wardrobe rods.
Two mounting possibilities for the side supports: on the sides of the module with a Ø3.5 wood thread screw or top mounting with an M6 screw.
M6x40 m screws are included for top mounting of the bar brackets.
Tube made of aluminium with a matte anodised finish, and supports made of aluminium-coloured painted plastic.
Tube made of aluminum with a black finish, and supports made of black plastic.
According to ISO standard: 7170:205, the bar can support a maximum weight of 40kg/meter evenly distributed.
FAQs - frequently asked questions:
What is the maximum weight that a clothes hanger bar bracket can hold?
According to standard ISO: 7170:2005, Emuca supports can support a maximum weight of 40 kg per metre, evenly distributed.
Furniture levelling foot with nut included. Designed to adjust and level all types of furniture with simple adjustment from the outside of the furniture. It has an M6 screw with a nut and a white plastic hexagonal cap.
External regulating leveler.
It has an M6 screw with a nut and a white plastic hexagonal cap.
It has a maximum height adjustment of 18 mm.
Made of steel.
Kit of supports for the Zero modular structure, composed of 3 sets of supports for wooden shelves and 1 set of supports for modules. Includes all the accessories for mounting on the profile.
Zero profiles and accessories for creating modular shelving. The profiles are made of aluminium and the joining accessories and supports are made of zamak, all with a textured black painted finish (RAL 9005). Thanks to its simplicity and design, you can quickly adapt the Zero system to any type of environment: home, dressing rooms, office and shops. You can combine different elements to create your ideal composition: wooden or glass shelves, modules or small cupboards and hanging rails. The Zero system is characterised by its ease of assembly, as it is not necessary to use any tools for adjustment. Adjust and position the shelves without having to disassemble any element and without special tools. Its great load capacity is noteworthy, as it can support more than 100 kg per shelf/module . In addition, with its innovative Zero fixing system, its clamping force increases as the weight it supports increases. The profile can be fixed using different mounting methods, fixing to the wall, floor or ceiling or combinations of both. The Zero system components include all the accessories necessary for assembly.
Kit of brackets for the Zero modular structure. It consists of 4 sets of brackets for wooden shelves, 1 set of bar brackets and a 1 m hanging bar. Includes all the accessories to mount it on the profile.
Zero profiles and accessories for creating modular shelving. The profiles are made of aluminium and the joining accessories and supports are made of zamak, all with a textured black or stone grey painted finish. Thanks to its simplicity and design, you can quickly adapt the Zero system to any type of environment: home, dressing rooms, office and shops. You can combine different elements to create your ideal composition: wooden or glass shelves, modules or small cupboards and hanging rails.
The Zero system is characterised by its ease of assembly, as it is not necessary to use any tools for adjustment. Adjust and position the shelves without having to disassemble any element and without special tools. Its great load capacity is noteworthy, as it can support more than 100 kg per shelf/module . In addition, with its innovative Zero fixing system, its clamping force increases as the weight it supports increases. The profile can be fixed using different mounting methods, fixing to the wall, floor or ceiling or combinations of both.
The Zero system components include all the accessories necessary for assembly.
Kit to create a modular shelving composition together with the Zero profile. Includes the supports to mount 4 wooden shelves and a 1 m hanging bar with its supports. The profile and the shelves are not included. You can purchase the profile by searching for the code 7022054 (8432393278131) or 7022154 (8432393278148).
Its design adapts to all types of environments and spaces: home, dressing rooms, office and shops. Combine the accessories with the profiles to create your ideal composition: wooden or glass shelves, modules or small cabinets and hanging rails.
High load capacity and different mounting methods: fixing to the wall, floor or ceiling or combinations of both.
Easy installation, as the profile can be fixed and adjusted without tools. All accessories and instructions for assembly are included.
Made of aluminium and zamak in textured black or stone grey painted finish.
Emuca - System for 2 supported wooden sliding doors, soft close, panels not included, Steel and aluminum, anodized
Flow sliding system in kit format for supported wooden doors. This kit includes all the necessary accessories for installing a two-door unit, except for the panels. The kit includes two soft-close devices for each door, providing cushioned opening and closing. It is designed for doors weighing up to 30 kg. The trolleys are made of steel and plastic with ball-bearing wheels that make the system glide smoothly. The trolleys also have an adjustment lock that is activated by a simple turn of a screw, in addition to having a 6 mm height adjustment. Its assembly is simple since the machining to be performed is the same on both the top and bottom of the furniture, since this system uses the same rail, which is designed in aluminum.
System for 2 wooden doors supported by an upper guide designed for installation in furniture.
Supplied in kit format, the packaging includes everything necessary for assembly in the furniture except the boards.
Both upper and lower carriages include ball bearings and 6mm adjustment as well as a lock.
The kit includes 2 soft-closing devices for each door designed for doors up to 30 kg.
Includes four 2.35m anodized aluminum profiles; two for each door, as the top one is identical to the bottom one.
Flow 2 surface-mounted sliding system in kit format for supported wooden doors. This kit includes all the accessories necessary to install a 2-door unit, except for the panels. The kit includes 2 inverted soft-closing devices, which allow the upper and lower carriages to be mounted symmetrically and achieve a cushioned opening and closing. Designed for doors weighing up to 30 kg. The trolleys are made of steel and plastic with ball bearing wheels which make the system slide smoothly. Likewise, these trolleys have an adjustment lock which is activated by a simple turn of a screw, as well as having a height adjustment of 9 mm. The assembly of the rails is very simple and fast since no prior machining is required to install them. All you need to do is screw in some clips to secure them at the top and bottom and then clip the surface rails. The length of the rails is 2.35m and is available in black painted and matte anodized finish.
System for 2 wooden doors supported by an upper guide designed for installation in furniture.
The installation of the surface rails in black painted finish is done using clips included in the kit.
Supplied in kit format, the packaging includes everything needed to assemble the unit except the boards.
Both the upper and lower carriages include ball bearings and 9mm adjustment as well as a lock.
The kit includes 2 reverse soft closing devices for each door designed for doors up to 30 kg.
Structures for creating shelves and solving storage problems in any room of the home, kitchen, living room or bathroom. This type of shelving is designed to create original shelving designs by combining them together.
They are available in three heights: 830, 1150 and 1790, both with a width of 350 mm that allows for a large storage capacity. They are made from highly resistant 25x10 mm steel tube, with plates that act as crossbars to place the shelves. The entire structure is painted in a high-quality black finish .
Installation is quick and easy, fixing the structure to the wall using holes created in the profile itself. The two highest measurements also include levellers, in case the shelving is fixed to the floor, to ensure that the structure is perfectly stable.
All accessories for assembly are included: 2 structures, screws and plugs (Ø6x30) to fix the structure to the wall, Ø3.5x15 screws in black finish to fix the wooden shelves to the structure, plastic plugs that hide the fixing of the shelf to the wall. In the case of the two highest structures, levelers are included.
Steel structure for making a shelving unit with 3 shelves. This type of structure is designed to create original shelving designs by combining them together.
The 830 mm high and 350 mm wide structure allows for a large storage capacity.
It is recommended to use shelves with a length of 690 mm and a thickness of 19 mm.
Easy installation by fixing the structure to the wall. The two structures for creating a shelf and all the accessories for assembly are included. Shelves not included.
Made of high quality black painted steel that ensures a long lasting finish.
Is it necessary to fix the structure to the wall if it is going to rest on the ground and appears to be very stable?
Yes, in any case the structure must be fixed to the wall to prevent it from tipping over.
This mechanism, using a set of pistons, lifts the base along with the mattress, revealing a useful surface for storing your duvet, sheet sets, clothes, toys or other objects.
This mechanism is compatible for 135 cm beds with a maximum weight of 60 kg respectively.
It is easy to assemble and includes all the accessories necessary for its installation. This mechanism is made of steel and has a high-quality and durable black lacquer finish.
Contains a set for 135cm beds (with 1150N pistons) with front opening and a maximum weight of 60kg.
Assistant mechanism for opening the chest/bed base.
Complete hardware for assembly is included.
Easy installation.
Black lacquer finish.
Set of 2 folding brackets for placing shelves on the wall . Available in sizes 203mm/303mm/403mm with a maximum load capacity of 40, 50 or 60kg per shelf with two brackets.
Easy to install, these folding brackets allow you to assemble folding shelves to make the most of the space. They have push buttons that allow you to fold them and activate the locking mechanism that prevents the brackets from accidentally folding.
Made of steel with a white painted finish. The supply includes 2 folding supports, 4 screws and 4 wall mounting plugs, and 6 wood screws for installation on the shelves you decide to use.
Set of 2 folding brackets for mounting shelves hanging on the wall.
Maximum load of 40/50/60kg for shelves with two brackets.
Locking mechanism prevents the brackets from accidentally folding.
Easy installation using the included screws.
Made of steel with black painted finish.
The Recycle removable recycling bin is ideal for separating and sorting household waste. Its structure has fully extendable ball bearing guides for manual access to the bins or automatically if fixed to the door.
It is characterized by its easy installation by screwing it to the bottom of the module with the screws included in the product. It can also be mounted on either the right or left side of the cabinet. It is suitable for modules with minimum useful dimensions of 265mm wide, 435mm deep and 400mm high.
It has two waste bins protected by a stainless steel casing, with a capacity of 12 litres each and a simple handle for easy removal. It is made of steel and plastic with an elegant anthracite grey finish.
Removable recycling container that allows you to separate and classify household waste.
It has fully removable ball guides for easy access manually or automatically if fixed to the door.
It is easy to install by screwing it into the bottom of the module with the screws included in the product. It can also be mounted on either the right or left side of the furniture.
For manual opening, use a 30 module with minimum internal measurements: Width 262 x Depth 435 x Height 400 mm and for automatic opening, use a 40 module with minimum internal measurements: Width 350 x Depth 450 x Height 400 mm
It is made of steel and plastic in an anthracite grey finish. It has two waste bins protected by a stainless steel casing, with a capacity of 12 litres each and a simple handle for easy removal.
Three-quarter-turn rotating shelves designed to maximize space in L-shaped corner kitchen cabinets. They are easy to install and adaptable to different unit heights. They are available in 800 mm and 900 mm unit sizes and in white and gray finishes . The system consists of two trays and mounting accessories made of recyclable, antistatic plastic, highly resistant to impact and UV rays, and a central aluminum bar with a matte anodized finish. They have a load capacity of 20 kg per tray .
Frequently Asked Questions
How to install corner kitchen cabinet trays – Shelvo?
The following video shows how to easily set up this storage system in a kitchen.
What is the load capacity of Shelvo corner kitchen cabinet trays?
All Shelvo corner kitchen unit tray models can support up to 20 kg of weight.
Removable, self-extracting recycling bin for 40 cm module. Once installed in the unit, the bin is removed when the door is opened . It is an excellent option for sorting waste. It is made up of a highly rigid plastic structure together with fully removable ball guides, which allow the bin to slide smoothly for better access to its interior. The bin has 3 10-litre bins with a handle for easy removal and cleaning.
For automatic installation, 40 modules are required with minimum internal measurements of depth 472 mm and height 445 mm and for manual extraction, 30 modules can be used. Its installation is very simple, allowing it to be installed in right or left opening modules and the structure of this waste bin is fixed to the bottom of the modules.
Made of steel and plastic in an anthracite grey finish. Includes all the mounting accessories necessary for installation in the kitchen.
Bottom-mounted waste container with automatic or manual extraction. For installation in right- or left-hand opening modules.
The extraction of the container and the opening of the lid are carried out automatically, activated by the door itself. It has a frame with ball guides that allow the container to slide smoothly.
It has three waste bins with a capacity of 10 litres and a handle for easy removal.
For automatic installation, 40 modules are required with minimum interior measurements of depth 472 mm and height 445 mm and for manual extraction, 30 modules can be used.
The set is made of steel and plastic in an anthracite grey finish.
Vertex kitchen and bathroom drawer kit with all the necessary elements for assembly. It is the optimal solution for your kitchen, bathroom or wardrobe furniture with an elegant design in anthracite grey and white . Each kit consists of all the necessary elements for the assembly of a 178 mm high drawer in modules with a side thickness of 16 mm . Includes: two side ribs, a set of soft-closing guides, a set of decorative covers and fixings for the front of the drawer.
The metal side ribs are made of steel with an anthracite grey and white painted finish, allowing the drawer front to be adjusted ±2mm vertically and ±1mm horizontally . The guides are fully extendable with soft closing and allow a maximum load of 60 kg for the drawer.
You will only need the boards cut to the correct dimensions for the bottom, back and border of the drawer.
Kit of hardware required for the assembly of a drawer with a height of 178 mm and a depth of 500 mm, except for the border, back and bottom.
Sized for 16mm board thickness for drawer bottom and back.
Synchronized full-extension guides, with cushioned closing and load capacity of 60 kg.
It has a 3D front adjustment: vertical using an eccentric of ±2 mm, horizontal ±1 mm, inclination -1.5/+4 mm.
Made of anthracite grey/white painted steel
Recycling bin ideal for installation on kitchen cabinet doors, facilitating the separation of waste and offering easier access to the bin.
Made of anthracite-grey plastic, it has a capacity of 15 litres and is very easy to fit inside most kitchen or bathroom furniture with a minimum internal width of 408mm. It is suitable for both left and right-hand door openings.
The bin remains hidden inside the cabinet when the door is closed, but the lid opens automatically when the door is opened. The bin is easily removed for easy cleaning.
Door-mounted container with a capacity of 15 litres.
Automatic opening of the lid when the cabinet door is opened.
Made of anthracite grey plastic.
Valid for furniture with a minimum internal width of 408mm with opening to both the right and left hand side.
The bucket can be easily removed for cleaning.
All accessories for assembly are included.
The Kaus LED luminaire is designed as lighting for kitchens and cupboards without the need for cables, with an elegant, extra-thin aluminium design. With this LED light you can illuminate the inside of your cupboards, the kitchen counter or the passageways of your home, with a warm, natural or cold white colour , as it allows you to vary the colour temperature. It is also a dimmable luminaire with which you can increase or reduce the luminous flux.
(Motion) It has an integrated twilight motion sensor that turns on the luminaire when it detects movement of people within its detection range (2 meters in length and an angle of 120º) and turns off automatically when it stops detecting movement, after 18 seconds. It also has a switch to turn the luminaire on or off manually.
(Proximity) It has an integrated proximity sensor that turns on the light when you pass your hand within its 7 cm detection range and turns off automatically when you pass your hand again. It also has a switch to turn the light on or off manually.
This luminaire has a rechargeable battery 850mAh lithium polymer battery with an autonomy of 400 18-second ignition cycles before the battery runs out. It is recommended to recharge the luminaire with a conventional mobile charger 5V DC 1A (not included) and a 30cm micro USB Type-C cable (included). The estimated full charge time is less than 2 hours, but varies depending on the size of the luminaire and the amperage of the charger. To check the charging status, it has an LED indicator that changes from red to green when charging is complete.
His Installation is very easy and simple , you just have to stick some adhesive metal bases on the surface of the furniture, without the need for cables or holes. The magnets incorporated inside allow it to adhere to the plates magnetically, and in this way the light can be easily removed for recharging.
LED luminaire that allows lighting for kitchens and cupboards without the need for cables, with an elegant extra-thin design and a length of 240/400/600mm.
It has an integrated twilight motion sensor that turns on the light when it detects movement of people within its detection range (2 m in length and 120º angle) and turns off automatically when it stops detecting movement, after 18 seconds.
The twilight sensor activates the light when the ambient light is below 250Lux, which extends battery life as it only turns on when really necessary.
It has a rechargeable 850mAh lithium polymer battery with a duration of 400 18-second ignition cycles, as well as a switch to turn it on or off manually.
The battery can be recharged with a conventional 5V DC 1A mobile charger (not included) and a 30cm micro USB type C cable (included), in less than 2 hours (LED charging status indicator).
Its installation is very simple, you just have to stick some adhesive metal bases to the furniture and the light fixture adheres magnetically, so it can be easily removed for recharging.
Screws and adhesive tape required for assembly are included.
Low-consumption LED technology.
Luminous flux of 60 lumens.
Power 1/2/3W.
Variable white colour temperature 3,000 - 4,000 - 6,000 Kelvin. Can be adjusted by pressing the side button or passing your hand over the sensor twice in a row.
150º light beam.
Luminaire suitable for dry areas, IP 20.
It is made of aluminum and plastic with a matte anodized finish.
FAQs - Frequently Asked Questions:
Can the Kaus luminaire be recharged with a mobile phone charger?
Yes, the Kaus luminaire can be recharged using a mobile phone charger. The charger must have a micro USB type C connector and must supply at least 5V DC 1A.
How long does it take to charge the Kaus luminaire?
Charging time will vary depending on the charger amperage. It is recommended to use 5V DC 1A chargers, so the estimated charging time is 2 hours.
How many cycles does the Kaus luminaire last to charge?
This light has an autonomy of 400 ignition cycles per charge before the battery runs out and has an LED indicator that changes from red to green when the charge is complete after approximately 2 hours.
Silver full extension concealed guides Perfect for home furniture. These guides provide full drawer extension and have push system ejection by pressing the drawer.
They stand out for their performance and feature a locking pivot mounted on the guide itself to prevent the drawer from being accidentally disassembled. They are made of steel and slide smoothly and quietly thanks to their high-quality Delrin rollers, which allow horizontal and vertical guidance.
Silver concealed full-extension push-pull drawer slides offer a modern and functional design, eliminating the need for handles. Their ejection system allows the drawer to open with a gentle push, while their safety lock prevents accidental removal. Made of high-quality steel , they provide smooth, quiet movement.
Frequently Asked Questions
Are the drawer dimensions (dimensions and machining) of the Silver full extension slides with push compatible with the Silver full extension slides with soft close?
Yes, the drawer dimensions and machining are fully compatible. This means that we can install the Silver full-extension slides with push-pull and the Silver full-extension slides with soft-close on the same drawer. However, they are not compatible with the Slippe full-extension slides with push-pull.
What are the locking pivots mounted on the Silver guides for?
The locking pins mounted on the Silver slides are designed to easily secure the drawers to the slides, preventing them from falling out during transport or handling. These pins eliminate the need for additional screws and only require a small hole in the side of the drawer rib to mount them. This allows the drawer to be assembled and disassembled as many times as desired.
How does the push-opening system of the Silver concealed guides work?
The push-open system allows the drawer to open automatically with light pressure on the front, eliminating the need for handles.
What feature prevents the drawer from opening unintentionally?
These guides have a locking pivot mounted on the guide itself, ensuring that the drawer remains closed until activated.
What is the vertical adjustment range of these guides?
The guides offer a vertical adjustment range of ±4.5 mm for precise drawer adjustment.
What materials are used in rollers and what advantage do they provide?
The rollers are made of Delrin, a high-quality material that guarantees smooth, quiet sliding and optimal horizontal and vertical guidance.
What load capacities can these full-extension slides support?
These full extension guides support a maximum load capacity of 30 kg.
Full extension drawer guides with smooth and silent sliding thanks to their high-quality ball bearings. They also stand out for their high load capacity , which can support up to 68 kg per drawer.
It is mounted to the drawer using screws and disassembled using a trigger on the guide itself.
Ball bearing guides for heavy-duty drawers and full drawer extension.
Made of galvanized steel.
Height 51 mm and length 400/500 mm.
Maximum load per set 68 kg.
Each lot includes 4 sets of individually packaged guides.
They have a trigger for removing the guide.
The system of Emuca Altius One compasses It stands out for its functional and versatile design, ideal for Lifting doors made of wood or aluminum . Their mechanism includes Fine adjustment , which allows precise force adjustment to ensure a free-stop experience. This ensures the door stays in any desired position, easily adjusted from the front using an adjustment screw once installed.
It is compatible with the use of a single mechanism or two , depending on the weight and size of the door, providing comfortable opening and closing. In combination with Emuca soft hinges, a smooth, bump-free closing is achieved , and it can be integrated with other types of hinges to adapt to different furniture configurations and custom designs.
This system is ideal for modules with little depth and fits to different door sizes and weights , offering a practical and efficient solution to optimize space and functionality in the kitchen and other spaces in the home.
For the distributors and wholesalers , this product represents a competitive and attractive solution. Available in three forces (low, medium and high) and two finishes Elegant (nickel-plated and titanium), the Altius One adapts to the needs of different market segments, facilitating the expansion of the product catalogue . The guarantee of compatibility with Emuca soft hinges and the inclusion of instructions Detailed instructions ensure that it is a practical and high-turnover option in any inventory.
Thinking about the carpenters and small businesses , this compass stands out for its ease of installation and adjustment , allowing for quick and hassle-free projects. Its functional design with mounting bracket and hardware included reduces work times , while its precise fit ensures a professional result without the need for additional tools. In addition, its price-performance ratio makes it a ideal solution for small and custom orders
Frequently Asked Questions
How do I install the Altius One compass on my furniture?
The following video shows how to easily assemble this system:
Can only one lifting system be used?
Yes, although using two devices provides greater stability during opening. Furthermore, it is recommended to use two lifting systems for doors wider than 1 meter.
He Uppsala furniture knob It is manufactured in aluminum and has a modern and contemporary design. It is designed for all types of drawer fronts and wardrobe doors , ideal for furniture kitchen, bathroom, home, and office . M4 screws for installation are included. Each knob is individually wrapped to prevent dents and scratches.
Lot of 10 furniture knobs
Diameter 30 mm.
M4 screws for installation included.
Made of aluminum with gold finish.
Individually wrapped to prevent scratches.
Only a standard screwdriver is required for installation.
Its aluminum construction with an anodized stainless steel finish makes it resistant to moisture, making it suitable for bathrooms.
Supra pull-out trolley with a functional and practical design, equipped with two wire baskets and a bread bag. A professional solution for maximizing storage in lower kitchen units and ensuring efficient food organization.
Designed for 300 mm wide modules, this accessory features optimized dimensions: 487 mm high, 245 mm wide, and 470 mm deep. Compatible with 16, 18, and 19 mm thick panels, ensuring precise and versatile installation.
Direct mounting to the base of the module, with full-extension guides and a cushioned closing system for smooth, quiet sliding. Its full border adjustment system allows adjustments in depth (±1.5 mm), horizontality (±2.25 mm), and height (±7.5 mm), adapting to different configurations.
High load capacity of up to 25 kg, ideal for supporting both food and utensils, ensuring efficient and safe use on a daily basis.
Made of steel with chrome finish.
He Supra pull-out trolley with baskets and bread basket It is the perfect solution for maximizing space in low kitchen units, facilitating the organization and accessibility of food. Its design includes two large baskets and a handy bread bag that helps keep food protected and organized.
The full extraction guides with soft close guarantee a quiet and comfortable glide. In addition, its system of adjustable regulation allows the mounting to be adapted in depth, horizontality and height, ensuring precise installation in different kitchen configurations.
Ideal for kitchens seeking efficiency and style, this cart is essential for improving accessibility and optimizing space inside kitchen cabinets.
The SupraMax pull-out bottle rack features three storage levels and three dividers in the lower basket, allowing you to efficiently organize bottles. It's the ideal solution for optimizing space in lower kitchen units, especially in small spaces.
(150) Compatible with modules with a minimum internal width of 112 mm, minimum depth of 460 mm and height of 800 mm. It has a load capacity of up to 30 kg.
(200) Compatible with modules with a minimum internal width of 162 mm, minimum depth of 460 mm and height of 800 mm. It has a load capacity of up to 30 kg.
Mounting is done on the left side of the cabinet using two fully extendable roller guides with soft-close mechanism. Compatible with 16, 18, and 19 mm boards.
It features full door adjustment: ±2.5 mm on the sides, ±2.25 mm in depth, and up to 13 mm in height. The sliding mechanism is smooth and silent, ideal for everyday use.
Made of chrome-plated steel rod with grey plastic separators.
Designed for 800 mm high modules, The SupraMax pull-out bottle rack is the perfect solution for optimizing storage in lower kitchen units, especially in small spaces. Designed to efficiently organize bottles , this model allows you to make the most of the auxiliary space in your kitchen cabinets. Thanks to its pull-out design , it offers easy and convenient access to the contents of its baskets, making it an ideal option for keeping your kitchen tidy. Made from steel rods , the SupraMax wine rack features a sturdy, durable construction . It fits on the left side of kitchen cabinets and is compatible with 16, 18, and 19 mm countertop modules . It features three levels of storage , with fully extendable, soft-close concealed runners for smooth, silent operation . Its 30 kg load capacity ensures optimal performance in everyday use, while its three dividers for the lower basket allow for flexible organization. The set includes the bottle rack , full extension guides , mounting screws and the three spacers, facilitating a simple and quick installation .
The Simplex drawer with metal sides is ideal for kitchen, bathroom, and home furnishings, without the need for special machining.
It allows the drawer front to be adjusted by ±2 mm vertically using an eccentric and ±1.5 mm horizontally, in addition to height adjustment thanks to the Silver L full-extension guides with soft-closing.
It offers a load capacity of 25 kg, guaranteeing resistance and smooth sliding.
Made of steel with a white painted finish.
Height 88:
It has a height of 88 mm with an elegant design, for drawers with a depth of 440 mm, offering great interior space and a modern finish.
Height 122:
It has a height of 122 mm with an elegant design, for drawers with a depth of 440 mm, offering great interior space and a modern finish.
Height 159:
It has a height of 159 mm with an elegant design, for drawers with a depth of 440 mm, offering great interior space and a modern finish.
The Simplex drawer with metal sides is the simplest and most versatile solution for having a metal rib drawer in kitchen, bathroom or home furniture , without the need for special machining. With an elegant design and a height of 88 mm , it offers a spacious interior and a modern finish. Its system allows the drawer front to be adjusted by ±2 mm vertically using an eccentric and ±1.5 mm horizontally . It also includes the Silver L full-extension guide with soft -closing and a load capacity of 25 kg , ensuring smooth and durable sliding. The kit includes two side panels , a set of front covers , a set of guides , and the screws to secure the front panel . It is made of steel with an anthracite gray or white painted finish.
Frequently Asked Questions
How do you install a Simplex soft-close kitchen, home, or bathroom drawer?
The following video shows how to easily assemble this drawer:
Take advantage of this limited offer:
10 universal kitchen drawer cutlery trays with a straight design and generous storage capacity for cutlery and other kitchen utensils, maximizing space. Because they are cuttable, they can be sized for use with drawers mounted in standard modules with a width between 400 mm and 900 mm , a depth between 450 mm and 500 mm, and a board thickness between 16 mm and 19 mm, depending on the model selected.
The unit costs €5.50
436x482mm cutlery tray sized for 500mm wide module drawers.
Adaptable to drawer depths between 450 mm and 500 mm with board thicknesses between 16 mm and 19 mm.
Can be cut to fit depths between 418mm and 482mm and widths between 400mm and 436mm.
Cutlery tray with 6 compartments for knives, spoons, forks, and all types of cutlery. For storing and organizing cutlery in your kitchen drawer.
Horizontal hinge for glass doors with aluminium trim, ideal for glass passage doors, display cabinets or shower doors. The hinge blade is 34 or 40 mm, can be installed on glass doors with a thickness of 8 to 12 mm and has a rotation range of 180º. It has eccentric rings that allow adjustment of ±2.5 mm. Two hinges support 60 kg and 3 hinges 90 kg. Made of aluminum . Includes a hinge and all mounting hardware.
Horizontal hinge for glass doors with aluminium trim. Ideal for glass doors, display cabinets or shower doors.
The hinge blade is 34/40mm, can be installed on glass doors with a thickness of 8 to 12mm and has a rotation range of 180º. It has eccentric rings that allow an adjustment of ±2.5 mm. Two hinges support 60kg and 3 hinges 90kg.
This hinge can be installed together with Emuca's stainless steel glass door cranks corresponding to code 9172614 or 9172714.
Made of steel and aluminum with black painted finish.
Includes one hinge and all mounting hardware.
